Page 1 of 1

Video Assist 4k does not work touchscreen

PostPosted: Tue Feb 06, 2018 7:45 pm
by VFedoseev
HI, on my Video Assist 4k does not work touchscreen!
HDMI signal coming.
Firmware - 2.5.2

Support is not responding!

HELP!

Re: Video Assist 4k does not work touchscreen

PostPosted: Tue Feb 06, 2018 8:23 pm
by VFedoseev
fideo proof:

Re: Video Assist 4k does not work touchscreen

PostPosted: Tue Feb 06, 2018 10:43 pm
by VFedoseev
Down to firmware 2.4 didn't solve problem

Re: Video Assist 4k does not work touchscreen

PostPosted: Wed Feb 07, 2018 2:52 pm
by VFedoseev
:twisted:
New - $895
Repair - $509
:twisted:

Blackmagic Support EMEA

Thanks for your email.

After taking a look at the serial number of your device, this does appear to be out of the warranty period meaning that any repair procedure we do conduct would be done at a cost.
We have determined that the following charges would be necessary in order to repair your product outside of it's warranty period:

Parts
Video Assist 4K - 7" LCD
$359.00

Labour
$100.00

Shipping
$50.00

To accept this quote, please reply back to this email in acceptance and confirm your invoicing details plus VAT number if applicable.

Please note, you will not receive any invoicing until we have received and tested the item and verified that the repair can be successful. This quote is not final. In the unlikely event that a repair should cost more than this, you will be contacted first. Unless otherwise specified, all prices are quoted without taxes and duties.

If you would like to go ahead with the return based on the conditions above, please complete the returns form below.

Please fill out the RMA form below in as much detail as possible, and copy it into the top of your response. It will need to be above the comment in order for it to come through.

Re: Video Assist 4k does not work touchscreen

PostPosted: Wed Feb 07, 2018 5:58 pm
by Denny Smith
Well, at least it is repairable, and you have an option here. At one time, if a repair exceeded 1/2 of the replacement cost, it was often replaced with a new bit, instead of being repaired.

That said, if the VA is otherwise in good kit, then the $500 repair (it might cost less, as this is a quote without seeing the VA to verify actual issue), is still 400 less than replacement. I would opt formthe repair in this case as it is just a little bit above 1/2 replacement cost.
Cheers

Re: Video Assist 4k does not work touchscreen

PostPosted: Thu Feb 08, 2018 11:08 am
by VFedoseev
It seems to me that this is very expensive. Repair should not cost more than $100. The problem is only in the touch screen. Maybe there's just a wire left.

Re: Video Assist 4k does not work touchscreen

PostPosted: Thu Feb 08, 2018 6:08 pm
by Denny Smith
Labor is reasonable, but parts seem a little high, but this is a 7-inch 1929x1080 HD touch screen.
Cheers

Re: Video Assist 4k does not work touchscreen

PostPosted: Thu Feb 08, 2018 6:58 pm
by VFedoseev
2018y .... 4k OLED monitor....

Re: Video Assist 4k does not work touchscreen

PostPosted: Fri Feb 09, 2018 2:42 am
by Denny Smith
OK. An OLED, that is why is is more than $300.
Cheers

Re: Video Assist 12g hdr does not work touchscreen

PostPosted: Thu Mar 03, 2022 4:57 pm
by ELYSE NSENGIMANA
I HAVE A BLACKMAGIC VIDEO ASSIST 12G HDR and its touch screen is no longer working properly.
only a column of 3cm is working on the left of the screen.
When I brought on eBay, it was new and was perfectly working.
After three months, the touch screen starts to deny responding from the right to the left of the screen

Does anyone know how to solve this issue?
THANK YOU!

Re: Video Assist 12g hdr does not work touchscreen

PostPosted: Tue Mar 29, 2022 12:04 am
by ELYSE NSENGIMANA
Does anyone know the process of solving my issue?

I have a video assist 7" 12G SDI (Serial Number: 7834978) and its touchscreen is not working properly.

I need a contact of someone who can fix it.

thank you!

Video Assist 4k does not work touchscreen

PostPosted: Tue Mar 29, 2022 4:17 pm
by rick.lang
Have you tried installing the latest version of the firmware? Even if you are using the latest version, removing the firmware from video assist and reinstalling it may help.

What camera are you using to connect to the video assist? More information might help us with suggestions. Your regional BMD Support may also help.

Re: Video Assist 4k does not work touchscreen

PostPosted: Fri Apr 08, 2022 7:22 pm
by ELYSE NSENGIMANA
rick.lang wrote:Have you tried installing the latest version of the firmware? Even if you are using the latest version, removing the firmware from video assist and reinstalling it may help.

What camera are you using to connect to the video assist? More information might help us with suggestions. Your regional BMD Support may also help.


Hi! I have tried everything without any positive response.

Re: Video Assist 4k does not work touchscreen

PostPosted: Fri Apr 08, 2022 10:55 pm
by rick.lang
What camera are you connected to when the touch screen is not responsive?

How are you powering the video assist, battery or with the mains power adapter?

What image do you see on the touch screen? Is it all black or On?