Blackmagic Forum

Even after restarting my secondary monitor goes mostly black when loading the fusion page. Never had this issue in the last few betas.

I really need this working asap as most of the work Im doing now is in Fusion. I un-installed and re-installed Fusion 15 final and its STILL black.

Turned secondary display off/one. That didnt work.

Reset UI settings and ended up with this... 2 panels restored but the third one still black

RESOLVED: (no pun intended)

What finally worked was turning off the dual display. Resetting the UI. Turning the 2nd display back on, and it worked. I think launching Fusion 9 may have been what started this mess. I had been switching back and forth between the fusion page and the edit page a lot the last couple days and never had any issues until launching Fusion 9 thismorning.

Still having problems with fusion and black boxes. Here now is my main display. Full of black boxes and I cannot do anything in fusion. No response.



Tried disabling dual monitors and resetting the UI. And it worked. Problem was my scrub bar was now at the beginning of my sequence. So I go back to my clip, go back into Fusion, and the black boxes were back! So I restarted Resolve. It booted up into the fusion page and everything was good. Did what I needed for the most part, then went back to the edit page. Needed to make one more tweak in Fusion so I went back to the fusion page and --- black boxes -- AGAIN. I cannot keep up with this. This has been happening since the beta versions and its making working in the fusion page untenable

Still having problems. Now every single time I go to the fusion page this is what I am greeted with.



Fusion was working SO much better in 15 and 15.1. What happened? Fusion so broken I literally am unable to use it at all anymore. Not exaggerating. I may have to downgrade.

(sorry pic is upside down. A distress signal I guess)

Video

Sorry its upside down again!


9 out of 10 times entering Fusion I see this. Please please fix this BMD. Fusion is completely broken if I cant see what Im doing

15.1, 15.1.1 and now 15.1.2 Fusion is still completely broken. How long will Fusion be broken guys?

....still....broken

I don't see any of these issues and with no one else reporting them its likely you should review the drivers for your GPU or some other config issue.

So disappointed. Still having this issue in 15.2.

I will check the drivers. But I am having this problem on two different machines. Both PCs with nvidia cards. Dont know what the issue is but that is what they have in common. I'll look into the drivers. *sigh*

Updated my GPU drivers to the new release two days ago. Still getting black windows when trying to use fusion. This is really frustrating because Fusion has become completely unusable for me. What else would you suggest trying?

Now, for the first time ever, and the first time in 15.2, my EDIT page is now all black.

I have had these issues on two machines, with various drivers and Resolve releases now since mid August. So for two months I've been reporting these issues. Can someone please help?? Not only is Fusion unusable now, but if this persists with the Edit page, Resolve is completely broken for me. 100% unusable. I would call tech support but my phone call keeps getting dropped on transfers. (Ive had this problem for a year now and Ive reported that before also) So I have to get someone to call me.

What else can I do? I just tried a complete re-install of Resolve, after deleting the old install. Still didnt work. Im out of ideas here.

Are your two graphics cards in SLI mode? If yes, disable it. Do you have an integrated graphics card enabled? If yes, disable it in the BIOS.

Gary Hango wrote:Are your two graphics cards in SLI mode? If yes, disable it. Do you have an integrated graphics card enabled? If yes, disable it in the BIOS.

Thanks for the help. But no and no. Custom built PC with two GTX 1080 Ti's. (only GPUs in the machine)

Peter Chamberlain wrote:I don't see any of these issues and with no one else reporting them its likely you should review the drivers for your GPU or some other config issue.

Another suggestions Peter? I'd really like to get this fixed so I can use fusion again.

Anyone???

I have had the exact same problem ever since Fusion was integrated. Still do on 15.2. It is absolutely unusable.

Switching over to Metal seems to fix this. I got other issues with Metal but Fusion UI seems to be ok.

i have same problem. i use 2 monitors and sometime i go fusion elements on first monitor with nodes goes black. i switch nodes on\of , switch 2nd monitor on \off on fusion and sometimes it go normal state. some time i need to restart davinci

puhovik wrote:i have dame problem. i use 2 monitors and sometime i go fusion elements on first monitor with nodes goes black. i switch nodes on\of , switch 2nd monitor on \off on fusion and sometimes it go normal state. some time i need to restart davinci

Thats exactly what I've encountered. When loading fusion the windows will be black. If I disable the dual screen option, and then re-enable it, the fusion comp will display correctly. Once in awhile Id have to restart. Im on windows so no metal option for me. I've got nvidia cards anyway.

any solutions? this bug can apear at start of using fusion. but can not apeat for a couple of hours

puhovik wrote:any solutions? this bug can apear at start of using fusion. but can not apeat for a couple of hours

Unfortunately not. In three months of reporting this issue I've only had one response from BMD and was told nobody else is having the issue and try updating the GPU drivers. Obviously I tried that and it did not fix anything. Asked for more help two weeks ago but so far, nothing.

FINALLY FIXED!!

THANKS GUYS!!!!!!!!

thx a lot!

Michael McCaffrey wrote:FINALLY FIXED!! THANKS GUYS!!!!!!!!

What was the solution?

Marc Wielage wrote:

Michael McCaffrey wrote:FINALLY FIXED!! THANKS GUYS!!!!!!!!

What was the solution?

I was told it was something related to the threadripper CPU. The developers were able to isolate and fix it. Beyond that I dont have any more info.