ATEM TV Studio - OUTPUT

Questions about ATEM Switchers, Camera Converter and everything live!
  • Author
  • Message
Offline

kmax1940

  • Posts: 1
  • Joined: Fri Feb 09, 2018 11:00 pm
  • Real Name: Kenny Johnson

ATEM TV Studio - OUTPUT

PostFri Feb 09, 2018 11:07 pm

Hello, our church just got a brand new ATEM Television Studio yesterday.

It looks like the ONLY output from the ATEM is SDI.

Can someone verify that?

I was hoping to output the ATEM to a PC via ESB so I could run it through FLME and stream to Youtube.
Offline
User avatar

Thomas Seewald

  • Posts: 1094
  • Joined: Fri Aug 24, 2012 11:57 am

Re: ATEM TV Studio - OUTPUT

PostSat Feb 10, 2018 12:19 pm

You are right. The USB is only for updates and the only output is SDI.

I don‘t know, wich way you made your streamings in the past, but you will need an additional hardware to do it with the TVS HD. I would suggest a small desktop with internal Mini Recorder, but also a notebook with USB video cards will do the job.
thos-berlin - Thomas S e e w a l d
Offline

Reinhold-Vienna

  • Posts: 9
  • Joined: Sun Feb 11, 2018 9:58 am
  • Real Name: Reinhold Klug

Re: ATEM TV Studio - IN/OUTPUT

PostSun Feb 11, 2018 10:41 am

ATEM Television Studio Pro
Hallo,

ich schreibe in Deutsch da mein Englisch nicht auf hohem Niveau ist.

Habe ein ATEM Television Studio Pro-Kontrol Panel erstanden um damit in Zukunft
3 - PTZ Kameras (an den HD-SDI Inputs) zu betreiben sowie an den HDMI Inputs
Laptops. Die Atem Software Version ATEM Switchers 7.3 wurde auf einem Laptop installiert
und damit läst sich das Bedienpanel via Ethernetverbindung auch bedienen.
Mein Problem: wenn ich einen Laptop (Windows Betriebssystem) an den HDMI-Inputs anschließe so ist kein Bild am Preview zu sehen. Habe verschiedene Laptops ausprobiert. Der einzige Laptop bei dem ein Bild zu sehen ist, ist von einem Macbook. Habe probiert die Einstellungen des Mischers zu verändern was auch keinen Erfolg gebracht hat. Input und Output Format: 1080P/50
Würde Unterstützung benötigen.

Greetings from Vienna - Reinhold ;)

I write in German because my English is not at a high level.

Have an ATEM Television Studio Pro-Kontrol Panel purchased in the future
3 - operate PTZ cameras (on the HD-SDI inputs) and on the HDMI inputs
Laptops. The respiratory software version ATEM Switchers 7.3 was installed on a laptop
and thus the operating panel can also be operated via Ethernet connection.
My Problem: if I connect a laptop (Windows operating system) to the HDMI inputs, there is no picture on the preview. Have tried different laptops. The only laptop in which a picture can be seen is from a Macbook. Have tried to change the settings of the mixer which has also brought no success. Input and Output Format: 1080P / 50
Would need assistance.
Offline

Wayne Rutherford

  • Posts: 49
  • Joined: Tue May 13, 2014 12:47 pm

Re: ATEM TV Studio - OUTPUT

PostSun Feb 11, 2018 2:02 pm

Is it this unit?
If so it is the only one that has a capture utility built in.
You can run Blackmagic Media Express to capture program to your hard drive.
I do not think that will help with a live stream but can give you a video on demand file to post after the event.
Attachments
atem.jpg
atem.jpg (130.04 KiB) Viewed 646 times
Offline
User avatar

Thomas Seewald

  • Posts: 1094
  • Joined: Fri Aug 24, 2012 11:57 am

Re: ATEM TV Studio - OUTPUT

PostSun Feb 11, 2018 3:14 pm

When „kmix“ writes, that he only found a SDI out, he has the „new“ TVS HD.

The old had an additional HDMI out and sends video over USB2. Ih this case, he could use „mxlight“ or „mxptiny“ for streaming.
thos-berlin - Thomas S e e w a l d
Offline
User avatar

Xtreemtec

  • Posts: 2488
  • Joined: Wed Jan 02, 2013 11:48 am
  • Location: The Netherlands

Re: ATEM TV Studio - OUTPUT

PostThu Feb 15, 2018 5:17 pm

Daniel Wittenaar .:: Xtreemtec Media Productions ::. -= www.xtreemtec.nl =-
4K OBV, ATEM TVS HD, 1M/E 4K, 2M/E Broadcast Studio 4K, Hyperdeck Studio Mini, SONY FS7 4K, Ursa Broadcast 4K
Offline

Reinhold-Vienna

  • Posts: 9
  • Joined: Sun Feb 11, 2018 9:58 am
  • Real Name: Reinhold Klug

Re: ATEM TV Studio - OUTPUT

PostSat Mar 31, 2018 10:01 am

my problem is now fixed - thanks to all :D

Return to Live Production

Who is online

Users browsing this forum: dartfreakz and 10 guests