URGENT HELP Needed

I know I shouldn't have tried to update the day before a shoot but I did thinking it would be fine but the update failed in the middle of it and no the camera is completely unresponsive and unrecognized by Blackmagic Camera Setup. I've tried multiple ports and USB C cables and nothing gets recognized.

This is a complete disaster and I need to get this camera back up in order to shoot tomorrow. Can ANYONE please give me advice on what steps to take to make that happen.

It's a BMPCC4k that was on I believe 6.2 and I was trying to install the latest. I had no accessories attached during the update. I'm using a Mac M1 Mini.

[Kristian Lam]

Hi,

1. Download and install Camera 7.7.3 from the support website:

To put the camera into recovery mode. To do this:
i. Disconnect all power sources and remove the battery to ensure that the camera is totally powered down.
ii. Connect power to the camera and power it up while holding down the focus button.
iii. Camera will power up with a blank screen and the fan should be running.

2. Once the camera is powered up in recovery mode, launch Blackmagic Camera Setup v7.7.3 and connect the camera to the computer via USB. This should now allow the camera to be detected by the computer. Click on the ‘Update’ button and allow the process to complete.

3. Once the update is completed, power cycle the camera. Then install Camera v7.9.

4. Now update the camera normally with Camera v7.9 and this should now be able to complete successfully.

My first born will now be named Kristian Lam. Thank you for sharing this. It worked.

I was not able to update. After successfully installing the 7.9 update onto my Mac Mini, powering up the camera, and connecting it to my Mac, I ran the update software and it found my Pocket Camera 4K.

I started the update process, but it failed suggesting I change cables. I then followed the recovery procedure here and tried again with another cable, but I got the same results.

I tried with all three USB C cables I own, but the update failed each time. My camera now has no software.

Parameters

Mac Mini 2020
Mac OS 11.1
Pocket Camera 4K version 6.2 (lens removed)
Update package 7.9

Any suggestions?

David

As a totally and illogically wildcard desperate measure, you could try :-

Remove media card and any other accessories.
Remove battery and other power sources.
Try to switch the camera on using the power button. It will of course not work.

Now connect power back to the camera.
Before you connect your USB cable to the camera, touch the shiny metal shield of the USB plug to the bare metal of the camera's lens mount first to draw off any static electricity or any stray voltage coming from the computer.
Try the firmware update process again.

Your next course of action if that does not work will be to try to update the camera with another computer. There may be something hostile happening between your computer and your camera. Older Macs had a sad habit of frying JVC HD*** firewire ports.

Thanks, Robert. I tried your suggestions, but it still didn't update.

I uninstalled the 7.9 updater and installed the 6.2 updater. That worked so my camera is working again.

I bought one of the first Pocket 4K's. I wonder if it's not compatible with version 7.9.

David

I had the same problem, only the camera was detected. The message said the update to 7.9 was done successfully, but not according to my camera it wasn't! WTH is going on?

OK, I now have 7.9 working on my pocket 4K, but I had to install an intermediate version. I installed 7.1 (which was reported by the camera as 6.9.6). Then 7.9 finally installed.

To summarize, I went from 6.2 -> 7.1 (6.9.6) -> 7.9

David

David White.

There is noting quite like a good outcome at the end of a distressing journey.

Do you need to install an intermediate version or could you just restart it and instantly install the latest version. Im not quite sure which version I had installed before trying to update and where I could get the older version

Does this fix work with the original URSA Mini 4.6k or is there another way?

7.9 doesn't do anything for that camera.