Beta 6
Posted: Thu Jul 12, 2018 6:01 pmProblem with Multicam - when I load a Multicam into the Source viewer it displays as 1x2 but when I select Multicam in the viewer menu the display goes blank.
Blackmagic Forum
https://forum.blackmagicdesign.com/
Beta 6
https://forum.blackmagicdesign.com/viewtopic.php?f=21&t=76413
Page 1 of 1
Posted: Thu Jul 12, 2018 6:01 pmRe: Beta 6
Posted: Thu Jul 12, 2018 9:10 pmIt's working fine for me here in Studio Beta 6 on Windows 10 Pro (1803).
Re: Beta 6
Posted: Fri Jul 13, 2018 1:21 amYou may need to tell us about your hardware and the format of the clips.
Re: Beta 6
Posted: Sat Jul 14, 2018 7:18 amMacbook Pro 15 Inch 2017
2.9Ghz Intel Core i7
16Gb 2133 Mhz LPDDR3
Radeon Pro 560 4096 MB
Intel HD Graphics 630 1536 MB
2TB External USB3 HD
Canon XF205 HD 1080P XDCAM422
Sony HD 1080P AC3 H.264
2.9Ghz Intel Core i7
16Gb 2133 Mhz LPDDR3
Radeon Pro 560 4096 MB
Intel HD Graphics 630 1536 MB
2TB External USB3 HD
Canon XF205 HD 1080P XDCAM422
Sony HD 1080P AC3 H.264
Re: Beta 6
Posted: Tue Jul 17, 2018 10:40 amI've tried with Resolve 14 too and the same result. Double click on the Multicam in the clip list. The Multicam loads in the source window (in my case two windows). The pointer changes to the Replace Clip style pointer (2 frames with pointers going between them). In order for it to work though the timeline needs to move in sync with the Multicam so as you make changes they are reflected in the timeline. In order for this to happen you are supposed to select the Multicam option in the Source window choice which lists Source, Offline, Audio Track and Multicam. Selecting Multicam changes the source back to traditional single video screen and doesn't provide the three icons for choosing audio/video, audio only and video only. I've captured a video of this and am happy to share it if it would be helpful. Thanks
Re: Beta 6
Posted: Tue Jul 17, 2018 12:55 pmSo far we can not repo your report, time to post a link to your video and your drp.
Re: Beta 6
Posted: Wed Jul 18, 2018 10:21 amhttps://www.dropbox.com/s/3eznf8qd7e7907g/Multicam%20issue.mp4?dl=0
You can see me hover over the two clips in the angle viewer, the Multicam is loaded in the timeline and when I hover over the menu it says 'Multicam' but when I then select Multicam from the menu the angle viewer disappears. Thanks
Keith
You can see me hover over the two clips in the angle viewer, the Multicam is loaded in the timeline and when I hover over the menu it says 'Multicam' but when I then select Multicam from the menu the angle viewer disappears. Thanks
Keith
Re: Beta 6
Posted: Wed Jul 18, 2018 1:28 pmI was able to create the Multicam mix using the keyboard shortcuts of 1 & 2 after setting it to switch video only in the menu.
Re: Beta 6
Posted: Fri Jul 20, 2018 9:19 amAh looking at the video, you are in single viewer mode.. thats new information.
Switch to dual viewer and see if that works as expected.
Switch to dual viewer and see if that works as expected.
Re: Beta 6
Posted: Fri Jul 20, 2018 2:31 pmHey,
Cannot understand what you do
First, switch to dual viewer, multicam is made to be used this way : on the right you see the TL viewer with your actual angle choice, on the left viewer you see your different angles you can click on...
So first : dual viewer please.
Then, on the left viewer, I think you'll want to click the "fit" choice (instead of this 100% burden I saw in the video
)
Then it will be ok for sure...
Cannot understand what you do
First, switch to dual viewer, multicam is made to be used this way : on the right you see the TL viewer with your actual angle choice, on the left viewer you see your different angles you can click on...
So first : dual viewer please.
Then, on the left viewer, I think you'll want to click the "fit" choice (instead of this 100% burden I saw in the video
)Then it will be ok for sure...