Blackmagic Forum

We just started using the BM Studio 4k cams and the focus and zoom controls during our church services. Even with the zoom speed dial all the way down, it feels like the zoom is way too fast. There's no way to have a nice slow push in or pull out. Is this something that can be addressed in a firmware update?

Which MFT lens are you using and seeing this behaviour?

This may sound like an odd question but just to be sure... have you adjusted the zoom speed dial on the zoom demand down to minimum?

Yes the speed dial is all the way down.

The lenses we are using is the Panasonic Lumix G X Vario PZ 45-175mm.

We have the same zoom speed issue when using LANC zoom/focus controllers on our Ursa Broadcasts. We've tried Libec and Manfrotto, both variable and speed control set to minimum. Lenses used are the Fujinon LA16 4K and 20x Canon HD. The zoom speed issue is the same with both lenses.

When we use these same LANC controllers with the Sony FX6, we get a smooth very slow zoom.

It would be good to have a zoom speed adjustment in the menu to account for different lens speed characteristics.

Tim Schumann wrote:Which MFT lens are you using and seeing this behaviour?

This may sound like an odd question but just to be sure... have you adjusted the zoom speed dial on the zoom demand down to minimum?

Is this something that can be fixed with firmware update to the camera?

We'll try and recreate it here...

In your Menu setup button mapping page for the Studio Camera can you check that you haven't set your zoom 'Speed' dial to another parameter? If you had set it to maximum and then mapped it to something else this could explain why the speed is staying high.

The issue LouisBacker is reporting sounds very different as that is via LANC on very different lenses and a totally different camera so is likely to be unrelated.

Tim Schumann wrote:We'll try and recreate it here...

In your Menu setup button mapping page for the Studio Camera can you check that you haven't set your zoom 'Speed' dial to another parameter? If you had set it to maximum and then mapped it to something else this could explain why the speed is staying high.

The issue LouisBacker is reporting sounds very different as that is via LANC on very different lenses and a totally different camera so is likely to be unrelated.

Everything is set correctly. I’ve checked many times. The speed dial DOES affect the speed when used. So I know it’s ser correctly. When we turn the dial up it goes faster. All I am saying is that, on the slowest setting, it’s still faster than I feel like it should be. The lowest setting should be a crawl. However it’s still much too quick for the lowest setting.

jpboyd58 wrote:

Tim Schumann wrote:We'll try and recreate it here...

In your Menu setup button mapping page for the Studio Camera can you check that you haven't set your zoom 'Speed' dial to another parameter? If you had set it to maximum and then mapped it to something else this could explain why the speed is staying high.

The issue LouisBacker is reporting sounds very different as that is via LANC on very different lenses and a totally different camera so is likely to be unrelated.

Everything is set correctly. I’ve checked many times. The speed dial DOES affect the speed when used. So I know it’s ser correctly. When we turn the dial up it goes faster. All I am saying is that, on the slowest setting, it’s still faster than I feel like it should be. The lowest setting should be a crawl. However it’s still much too quick for the lowest setting.

Ditto here. We can only vary the zoom speed from moderate to fast. Although as Tim points out, we're on Ursa Broadcast G1/Fujinon LA16 with LANC control, not your same set-up. The Ursa Broadcast similarly does not zoom at "crawl" speed, even though they zoom very slowly with our Sony FX's, so it must be down to how the Ursa Broadcast is interpreting the LANC signal.

So yes, if there was a menu parameter to reduce speed further, we'd have better use of this camera, i.e. for interviews and static presenters. After all, what's the benefit of the camera having LANC control jacks, if it's implementation is limited?

jpboyd58 wrote:

Tim Schumann wrote:We'll try and recreate it here...

Everything is set correctly. I’ve checked many times. The speed dial DOES affect the speed when used. So I know it’s ser correctly. When we turn the dial up it goes faster. All I am saying is that, on the slowest setting, it’s still faster than I feel like it should be. The lowest setting should be a crawl. However it’s still much too quick for the lowest setting.

Okay will check it out.

Tim Schumann wrote:

jpboyd58 wrote:

Tim Schumann wrote:We'll try and recreate it here...

Everything is set correctly. I’ve checked many times. The speed dial DOES affect the speed when used. So I know it’s ser correctly. When we turn the dial up it goes faster. All I am saying is that, on the slowest setting, it’s still faster than I feel like it should be. The lowest setting should be a crawl. However it’s still much too quick for the lowest setting.

Okay will check it out.

Great too if the Ursa Broadcast (Gen 1) LANC speed could be looked into at the same time. Thank you.

I second this. The zoom speed when dialed all the way down is still too fast.

We are looking into this.

That said... have you ever seen zoom speed move slower on this Micro 4/3 45-175mm power zoom lens on another camera? We can only go as fast, or slow as the lens servo will allow.

Tim Schumann wrote:We are looking into this.

That said... have you ever seen zoom speed move slower on this Micro 4/3 45-175mm power zoom lens on another camera? We can only go as fast, or slow as the lens servo will allow.

Ursa Broadcast Gen1. Using the on-lens zoom controls on our Fujinon LA16 4K and Canon KJ20x8.2B IRSD B4 lenses, I can confirm that their servos operate down to a "crawl" speed. When using the Manfrotto or Libec Lanc controllers, the minimum zoom speed I'd say is approx 20% faster than that achieved with the on-lens rocker control, as if the camera's Lanc range is running 20-100%, instead of 1-100%.

Tim,

We have the same 45-175mm lens referenced. We have a few non-BlackMagic cameras in addition to our Studio 4K Pro cameras, so we’ll give those a shot and see if zoom is any slower on this and report back.

openlog wrote:Tim,

We have the same 45-175mm lens referenced. We have a few non-BlackMagic cameras in addition to our Studio 4K Pro cameras, so we’ll give those a shot and see if zoom is any slower on this and report back.

What LANC controls are you testing with the Panasonic lenses?

We tried those Panasonic 45-175mm lenses as well. I don't believe they're physically capable of zooming any slower. If you unplug the Zoom Demand for a moment and try slow zooming with the manual zoom ring, you will find it stutters if you go too slow. In my research I have not been able to find an MFT lens that can do a slow servo zoom. There is a Canon EF lens with a better built-in servo that can be adapted to the Studio 4k MFT mount, but that would set you back about $5k.

In my opinion, until there is an MFT lens with a slower, smoother servo, the Zoom Demand is useless for slow zooms. This is part of the reason we decided to purchase the Panasonic Leica 50-200mm instead. Figured we might as well get the higher quality lens if we're not going to be able to slow zoom either way, and we really don't do a lot of zooming anyway.

Zoom is manual on the 50-200mm lens, but it still works with the Focus Demand. Image is nice and sharp, even zoomed all the way in.

I don't know of this "too fast" zoom issue has been addressed yet for the Ursa G2, as I only have G1s?

LANC contol on the Ursa G1 exhibits similar problems, with the lowest zoom speed setting being too fast for practical use (both Libec & Manfrotto lanc controls). Yet, when I plug the same controllers into a Sony FX6, bingo, you can zoom at a slow crawl. Clearly, Blackmagic's processing of the LANC zoom speed is so that it's not useable. And to boot, you get two Lanc ports; neither zoom-friendly.

To overcome this slow zoom speed issue on the Ursa G1, I use a Libec ZC-9Pro (£111 off Amazon) straight into the lens's 8-pin connector. Now I can zoom from very fast to smooth slow crawl. Problem solved. There is a switch to select Canon or Fujinon. Lenses tested; Fujinon LA16 8BRM (the 4K bundle lens) and Canon KJ20x8.2B KRSD (nice 20x zoom HD lens). The Fujinon is a tad smoother when slow-starting the zoom.

Dear Blackmagic Team. My first post, and I just got my first BM products, the URSA Broadcast G2 among them. I use a Canon KJ17ex7.7B IASE II S. This lens is capable of a very slow crawl zoom speed, which is more or less the only speed I use when filming music, like classical orchestra, except when adjusting framing. The in point for the BM zoom demand is way too fast, almost like a shock zoom compared to the desired crawl speed the lens in itself can do. In fact, the BM zoom demand overrides any speed adjustment made in the lens internally. I can understand the override, but I am sure it is only a matter of firmware adjustment to change the starting speed and a finer resolution of the BM zoom demand.

Is this being looked into? Otherwise, I have bought a zoom demand totally useless to my use.

Jens Daniel Sagen Johannesen

+1

jensda wrote:
Is this being looked into? Otherwise, I have bought a zoom demand totally useless to my use.

Jens Daniel Sagen Johannesen

Ditto +1. I purchased 2 x Blackmagic Zoom demands this summer, primarily to use the Zoom Speed dial re-mapped to Iris Control. The zoom element remains unusable speed-wise for corporate presentations/interviews (yet as I've mentioned previously, the much cheaper Libec zoom demand works superbly). Our camera combo is UB G2 with the bundled Fujinon LA16 4K lens.

+1 on Canon CN-E 18-80 + Ursa Broadcast G2