Blackmagic Forum

hello,
wanting to interface studio cameras 4K pro with a constellation 8K, the Blackmagic 2110 IP Converter 4x12G PWR seems to be the best solution.
But on the converter's web page, only the studio 6K pro is expressly mentioned.

should we consider that 4K studio camera will not benefit from the ip2110 ?

You’ll need a converter


Sent from my iPhone using Tapatalk

There is no IP 2110 support for any of the Studio Camera models as of yet. An update for these models is TBD. You can use the Studio Converter for these models to power and connect via 10G Ethernet (which is not 2110) for now. I hope this helps.

Gary

Gary Adams wrote:An update for these models is TBD... I hope this helps. Gary

Thanks for answer Gary. I'm glad you confirmed that Studio 4K and 6K pro cameras will work with 2110 IP Converter 4x12G PWR in the future.
I can pre-order one

Videobegin wrote:

Gary Adams wrote:An update for these models is TBD... I hope this helps. Gary

Thanks for answer Gary. I'm glad you confirmed that Studio 4K and 6K pro cameras will work with 2110 IP Converter 4x12G PWR in the future.
I can pre-order one

TBD = To be decided! (Or determined..)

Hi Louis thanks for correction, I read TBD = To Be Done

Yeah I wouldn't order one until the feature is shipping.

Multiple times in the past few years features have been promised that never materialised.
A recent example is the Decklink IP cards which were sold as being 3 channel with only 2 channels supported in the initial firmware. A year later, and the published specs of the device now say they support 2 channels.

Videobegin wrote:Hi Louis thanks for correction, I read TBD = To Be Done

Ha yes, you could be right - hopefully!

Hi everyone,

I recently got a Blackmagic 2110 IP Converter 4x12G and paired it with Blackmagic Studio Camera 4K Pro G2. To my surprise, I found that I couldn't receive any video feed over the Ethernet (Cat6) cable coming out of the camera — only power it via PoE from the converter.

During the 2024 NAB presentation about 9 months ago, Grant Petty mentioned that SMPTE 2110 support for the Studio Cameras would be added via a software update in just a few weeks.

You can watch the presenation on Youtube at around 58:50 mark on Blackmagic Youtube channel NAB 2024 Update. "This software update should be available in a few weeks time"

Yet, here we are in 2025, and I’m unable to make it work. Am I missing something, or has this update still not been released?

Any insights or updates would be appreciated!

Daniels wrote:Hi everyone,

I recently got a Blackmagic 2110 IP Converter 4x12G and paired it with Blackmagic Studio Camera 4K Pro G2. To my surprise, I found that I couldn't receive any video feed over the Ethernet (Cat6) cable coming out of the camera — only power it via PoE from the converter.

Unfortunately, I’ve got some bad news for you. As already mentioned, Blackmagic Design has a track record of announcing features that either take forever to be implemented or never get implemented at all.

From my experience, I don’t buy Blackmagic products until the needed functionality is written in bold letters on the product page. For example:

Blackmagic Camera/Studio Converter. Released over 6 years ago, and the Ethernet port still not implemented. Just “TBD.”
Constellation 8K. Broken audio routing. They released a crippled workaround 5 years after launch. The issue was only partially fixed, and chances are, that’s as good as it’s going to get...
So yeah, better be cautious with their promises.
But don’t get too disappointed. NAB is coming up soon, and they usually drop big releases right before the show.

Hey everyone,

To mu surprise Blackmagic’s official Instagram post (from the release of Ultimatte 2.2 update) says:

"That means you can now choose between SDI or 2110 IP for the foreground input, giving you a wider range of options for compositing, including footage from cameras with 2110 IP such as Blackmagic Studio Camera."

This statement suggests that the Studio Camera 4K Pro supports SMPTE 2110, but from what we’ve learned, this isn’t the case.

So, what’s the truth here? Has the firmware update for 2110 been released for the Studio Cameras, or is this just incorrect wording in the Instagram post? Can Blackmagic clarify this?

Thanks!

As I wrote, only the studio 6K pro is expressly mentioned for IP2110 use. No confirmation for 4K model. And no delay for firmware update.

The firmware for 2110 support in the Studio Camera 4K/6K Pro cameras has not been released yet but we expect soon. I hope this helps.

Gary

Thanks Gary for your confirmation about 4K model.

@Louis, it's to be done

Thanks, Gary, for the clarification!

So, just to confirm—right now, the Blackmagic Studio Camera 4K Pro does not support SMPTE 2110 video over Ethernet, but a firmware update is planned and expected soon.

Looking forward to the firmware release! Thanks again.

Hello Daniels. Yes, it is expected in a firmware update. We have been showing it at trade shows but the firmware is not quite ready.

Gary

Gary Adams wrote:Hello Daniels. Yes, it is expected in a firmware update. We have been showing it at trade shows but the firmware is not quite ready.

Gary

Hi Gary, frankly speaking I am a bit amazed and shocked by the approach of your company: to present the equipment, to put it on sale and at the same time not to make firmware for the most important feature of this equipment ... I spent about 6 thousand euros to buy cameras and converter in the hope that everything will work as stated by the manufacturer, and it turns out that I have to put all this equipment in a far corner and wait for firmware update.... Please clarify when exactly this firmware is planned to be released?

Thank you!

I'll write another post, as the previous one seems to have failed moderation.....

Guys, I have a question: I bought an Blackmagic 2110 IP Converter 4x12G PWR for 2200 euros and all it can do is supply power via twisted pair to the Blackmagic studio 4k pro G2 cameras, which I bought 2 of them for 1850 euros per camera? So I now have a power supply for 4 cameras for 2200 euros? When do you plan to make a new firmware for the camera, because without the function of transferring the picture over twisted pair at least IP converter just useless hardware ...

Hi,

Same here, bought an 2110 4x12G as we have 4 Studio Cameras 4K Pro.

BMD in their website clearly states, and i quote:

With 10G Ethernet on the Pro models, you can connect all signals to the camera with the one simple SMPTE-2110 IP Ethernet connection. That means the camera feed, return program feed, timecode, reference, tally, talkback and control are all sent down the single cable. Even camera power!

So, where do we go from here? Do we return the equipment? Will BMD provide some more details rather than TBD?

I'm a Newtek (now Vizrt ) user and i was really hoping to replace our TC2 and TC1 with BMD equipment, but this kind of behaviour doesnt transmit much confidence.

Regards

FINALLY! IT WORKS! 06.04.2025. Blackmagic Camera 9.4 Beta

Blackmagic Studio Camera 6K Pro
Blackmagic Studio Camera 4K Pro
Blackmagic Studio Camera 4K Pro G2
Blackmagic Studio Converter
Adds 2110 support over the 10G Ethernet connection.

I've just updated and it now works like a charm. Thank you Blackmagic for making this!