Sound Devices MixPre-6 II (second generation)

The place for questions about shooting with Blackmagic Cameras.
  • Author
  • Message
Offline
User avatar

rick.lang

  • Posts: 17175
  • Joined: Wed Aug 22, 2012 5:41 pm
  • Location: Victoria BC Canada

Sound Devices MixPre-6 II (second generation)

PostSun Sep 29, 2019 4:57 am

I was forgetting Audacity doesn’t handle Timecode. Does Reaper keep the Timecode?

Edit
I keep my MixPre on a mic stand, not on or under the camera. Of course that’s when I’m tripod bound anyway.

Sent from my iPhone using Tapatalk
Rick Lang
Offline
User avatar

rick.lang

  • Posts: 17175
  • Joined: Wed Aug 22, 2012 5:41 pm
  • Location: Victoria BC Canada

Sound Devices MixPre-6 II (second generation)

PostSun Sep 29, 2019 5:05 am

Ian, I don’t mind the 19msec delay as I seldom put headphones on, looking at audio levels though. The AVX works well with the talent in line of sight. And through some thin barriers as found on a set. Today was the first day I was using the AVX and the EW500 G4 Boom. Haven’t listened to them as I was exhausted. Couldn’t get levels for either in the MixPre even though I did on my testing. Bit of a mystery but the Line Audio Design CM-4 mics seemed great.


Sent from my iPhone using Tapatalk
Last edited by rick.lang on Sun Sep 29, 2019 2:41 pm, edited 1 time in total.
Rick Lang
Offline

Paul Curtis

  • Posts: 47
  • Joined: Fri Dec 07, 2012 10:01 am

Re: Sound Devices MixPre-6 II (second generation)

PostSun Sep 29, 2019 11:25 am

So i switched from F4 to Pre6 II and i think it's awesome. It is way simpler to use and just a better UI and approach. The float is fantastic as i did a side by side with the Zoom. Does what it says. Life will be a little easier now!

I need Resolve to support float properly though, i can use audition but clearly resolve is the right place for it.

As for TC, i jam sync'd off a tentacle and after an hour at 25p it's still locked. I am turning the device off as well, not leaving it on but i am powered via USB C. I will keep checking.

What i'd be tempted to do though is perhaps drive the tentacle with the TC out from the recorder and getting that master tentacle to sync the slaves on camera. That should work shouldn't it? I'm just a bit wary of jamming TC but will see how that goes... Plus i like t he idea of 2 additional tracks from the Aux In...

cheers
Paul
Offline
User avatar

rick.lang

  • Posts: 17175
  • Joined: Wed Aug 22, 2012 5:41 pm
  • Location: Victoria BC Canada

Re: Sound Devices MixPre-6 II (second generation)

PostSun Sep 29, 2019 2:46 pm

I repeatedly felt that jamming the Tentacle from the MixPre 3.5mm Stereo Out seemed problematic and using the Aux1 In to jam the MixPre from my master Tentacle was better. Either way should be fine, but I’ll temporarily tie up Aux1 rather than the Stereo Out.


Sent from my iPhone using Tapatalk
Rick Lang
Offline
User avatar

dondidnod

  • Posts: 633
  • Joined: Sun Nov 25, 2018 7:52 am
  • Location: Castro Valley, CA
  • Real Name: Donald Keller

Re: Sound Devices MixPre-6 II (second generation)

PostTue Oct 01, 2019 8:18 am

Bill Hall wrote:One big difference between sound devices and other manufacturers is RF noise rejection. On sets their is more RF noise than ever. I have been having increasing noise issues with the zoom F8 due to RF noise.

Sound Devices has great design for RF noise rejection.

I just got my Sound Devices MixPre6 II from Adorama after a wait of 10 days on backorder.

I had done some ADR for a class assignment using the school's Zoom F8 recorder (same preamp as the F6) and an Azden shotgun Mic at 12 inches away in a college computer lab. When I tried using it at a workstation that was located five feet from fluorescent lights, all I got was a loud hum and could barely hear my voice, no matter how much I moved the xlr cable. I then moved to another workstation located seven feet from the overhead fluorescent lights and was able to get a recording, Occasionally I would get a lighter hum that went away when I twisted the school's xlr cable.

I re-recorded the ADR using the new MixPre6 II at 24 bit, with my new Sennheiser MKE-600 supercardiod Mic at 12 inches with a lightly used Kopul 5000 xlr cable. I did it at the same location that was five feet away from the lights that produced the loud hum before. To my surprise it sounded quite nice, and more natural than the F8, with the airy sound that you get from a preamp with real headroom. It was usable in spite of the harsh RF interference.
Offline
User avatar

Dmytro Shijan

  • Posts: 1760
  • Joined: Wed Sep 17, 2014 7:15 pm
  • Location: UA

Re: Sound Devices MixPre-6 II (second generation)

PostTue Oct 01, 2019 10:18 am

Some photos of MixPre-3 (first generation) internal components from this source https://fccid.io/2AKLX-739M3/Internal-P ... os-3297643

Image
Image
Image
Image
Image
Last edited by Dmytro Shijan on Fri Nov 01, 2019 9:44 pm, edited 1 time in total.
BMMCC/BMMSC Rigs Collection https://bmmccrigs.tumblr.com
My custom made accessories for BMMCC/BMMSC https://lavky.com/radioproektor/
Offline

Tom Donalek

  • Posts: 49
  • Joined: Wed Apr 23, 2014 4:31 pm

Re: Sound Devices MixPre-6 II (second generation)

PostTue Oct 01, 2019 7:14 pm

OwenCrowley wrote:Resolve's inability to process 32bit float audio will probably force me to record at 24bits.


I've been checking in periodically to see if there is any sign of progress on this. Has Blackmagic acknowledged that they are aware of the 32 bit float problem, or made any statement that they are working to address it?
Offline
User avatar

Rakesh Malik

  • Posts: 3236
  • Joined: Fri Dec 07, 2012 1:01 am
  • Location: Vancouver, BC

Re: Sound Devices MixPre-6 II (second generation)

PostTue Oct 01, 2019 7:56 pm

Tom Donalek wrote:I've been checking in periodically to see if there is any sign of progress on this. Has Blackmagic acknowledged that they are aware of the 32 bit float problem, or made any statement that they are working to address it?


Not yet, at least not publicly as far as I've seen.
Rakesh Malik
Cinematographer, photographer, adventurer, martial artist
http://WinterLight.studio
System:
Asus Flow X13, Octacore Zen3/32GB + XG Mobile nVidia RTX 3080/16GB
Apple M1 Mini/16GB
Offline
User avatar

rick.lang

  • Posts: 17175
  • Joined: Wed Aug 22, 2012 5:41 pm
  • Location: Victoria BC Canada

Re: Sound Devices MixPre-6 II (second generation)

PostTue Oct 01, 2019 8:13 pm

Has anyone confirmed that Reaper will preserve Timecode values on their output? I’m going to try hopefully this week but working on some other issues as a top priority. Hope it’s in Resolve 16.1 GM.


Sent from my iPhone using Tapatalk
Rick Lang
Offline
User avatar

Dmytro Shijan

  • Posts: 1760
  • Joined: Wed Sep 17, 2014 7:15 pm
  • Location: UA

Re: Sound Devices MixPre-6 II (second generation)

PostThu Oct 03, 2019 5:31 pm

Looking at photos of MixPre-3 internals i can't understand where are all those well known analogue transformers that amplify microphone signal? Are they change something and amplification is done in completely different way now? Maybe that is a reason why some people noticed during testing that new models sounds different with less character?
Here is image of older "Classic" MixPre to compare. You can clearly see two large transformers.

Image
BMMCC/BMMSC Rigs Collection https://bmmccrigs.tumblr.com
My custom made accessories for BMMCC/BMMSC https://lavky.com/radioproektor/
Offline

Ian Henderson

  • Posts: 208
  • Joined: Wed Aug 22, 2012 8:05 am
  • Location: Cape Town, South Africa

Re: Sound Devices MixPre-6 II (second generation)

PostThu Oct 03, 2019 5:54 pm

Looks like metal XLR sockets replaced with plastic too.
Offline

Username

  • Posts: 389
  • Joined: Tue Jun 25, 2019 2:33 am
  • Real Name: Petter Flink

Re: Sound Devices MixPre-6 II (second generation)

PostThu Oct 03, 2019 6:16 pm

Those Lundahls are specific for microphones.
They convert balanced in to unbalanced. They galvanically separate its input side from the output making sure no signals travel through ground.
As they are transformers they are very hard to overload and saturate. They handle +12dBU quite ok.
Grew up with a Nikon FM
Resolve & Fusion Studio 18.6
MBP M1 16GB/1TB
MM M1 16GB/512GB TB4 1TB & 2TB
MM i7 16GB/1TB & PowerColor Vega 56 8GB
Offline
User avatar

rick.lang

  • Posts: 17175
  • Joined: Wed Aug 22, 2012 5:41 pm
  • Location: Victoria BC Canada

Re: Sound Devices MixPre-6 II (second generation)

PostThu Oct 03, 2019 10:03 pm

On the question of power to the MixPre-6 II:
The DC Power supplies 5V. Okay.

The recorder can run from a four battery sled. The batteries can be 1.5V. Used serially, the batteries are 6V one time use or about 5V rechargeable. I have a Li-ion.

I bought larger Sony L-series batteries so I wouldn’t have to think about batteries on a very long day. The salesman over the phone suggested the Sound Devices XL-B3 and I ordered two with charger. The online documentation for the MixPre says you need to mount two of the large batteries.

Today I got them and each battery is 7.4V 7800mAh. It looks like it will take forever and a day to charge one battery in the puny single battery charger.

Does anyone know if both batteries are required to be mounted in the MixPre sled for proper operation?

If both are required, just how many hours will these batteries last between charges, 600 hours!?

Thanks!


Sent from my iPhone using Tapatalk
Rick Lang
Offline

Bob Moore

  • Posts: 94
  • Joined: Tue Apr 25, 2017 2:33 am

Re: Sound Devices MixPre-6 II (second generation)

PostFri Oct 04, 2019 1:47 am

No Rick,

I always use one on the top slot so that the unit can sit flush on a surface.

Watson makes an expensive dual charger that shows levels ... works great and will charge both in
a couple of hours.

https://www.bhphotovideo.com/c/product/ ... r_for.html

The battery plates are changeable ... for Sony, Nikon, Canon etc.
Offline

Username

  • Posts: 389
  • Joined: Tue Jun 25, 2019 2:33 am
  • Real Name: Petter Flink

Re: Sound Devices MixPre-6 II (second generation)

PostFri Oct 04, 2019 3:59 am

The 7.4v li-ion packs you can mount are hot swappable.
You can run a single is what ever mount you like and add the second one before you remove the first if it’s depleted. Or you run them both at the same time.

When I asked about the first series the battery mount accepts 4-8.4v input.
So the third party sleds which offers 10-30v Hirose input simply run a dc-dc inside them to reduce that down to 8V.
Grew up with a Nikon FM
Resolve & Fusion Studio 18.6
MBP M1 16GB/1TB
MM M1 16GB/512GB TB4 1TB & 2TB
MM i7 16GB/1TB & PowerColor Vega 56 8GB
Offline
User avatar

rick.lang

  • Posts: 17175
  • Joined: Wed Aug 22, 2012 5:41 pm
  • Location: Victoria BC Canada

Re: Sound Devices MixPre-6 II (second generation)

PostFri Oct 04, 2019 4:13 am

Thanks for the feedback. I have been charging a single battery for over eight hours! Still a red light.


Sent from my iPhone using Tapatalk
Rick Lang
Offline
User avatar

Robert Niessner

  • Posts: 4946
  • Joined: Thu Feb 21, 2013 9:51 am
  • Location: Graz, Austria

Re: Sound Devices MixPre-6 II (second generation)

PostFri Oct 04, 2019 5:57 am

Rick, the Atomos Fast Charger for the NP-F batteries charges a 5200mAh in 3 hours, which is 1733mAh per hour. For your 7800mAh it would need 4.5 hours. So I guess with your slow charger it will take 13.5 hours for your battery.

The review on B&H on the Sound Devices charger says it all:
https://www.bhphotovideo.com/c/product/ ... ml/reviews
Saying "Thx for help!" is not a crime.
--------------------------------
Robert Niessner
LAUFBILDkommission
Graz / Austria
--------------------------------
Blackmagic Camera Blog (German):
http://laufbildkommission.wordpress.com

Read the blog in English via Google Translate:
http://tinyurl.com/pjf6a3m
Offline
User avatar

Dmytro Shijan

  • Posts: 1760
  • Joined: Wed Sep 17, 2014 7:15 pm
  • Location: UA

Re: Sound Devices MixPre-6 II (second generation)

PostFri Oct 04, 2019 6:20 am

So i recover some info from PCB photos and found this:

:arrow: AKM AK5558VN A/D chip https://www.akm.com/global/en/products/ ... /ak5558vn/

:arrow: ZYNQ 7000 SoC FPGA chip https://www.xilinx.com/products/silicon ... -7000.html
Last edited by Dmytro Shijan on Fri Oct 04, 2019 6:39 pm, edited 1 time in total.
BMMCC/BMMSC Rigs Collection https://bmmccrigs.tumblr.com
My custom made accessories for BMMCC/BMMSC https://lavky.com/radioproektor/
Offline
User avatar

Dmytro Shijan

  • Posts: 1760
  • Joined: Wed Sep 17, 2014 7:15 pm
  • Location: UA

Re: Sound Devices MixPre-6 II (second generation)

PostFri Oct 04, 2019 7:38 am

Ian Henderson wrote:Looks like metal XLR sockets replaced with plastic too.

Less weight. Also those Neutrik XLRs are made of Polyamide (Nylon). It is very rugged heat resistant industrial material. https://www.neutrik.com/en/product/ncj6fa-h

To be honest i never liked metal XLR connectors for field recording work. Earlier i done a lot of modifications to XLRs shells (original Neutriks) and it appears that they are made of very soft and heavy alloy.
BMMCC/BMMSC Rigs Collection https://bmmccrigs.tumblr.com
My custom made accessories for BMMCC/BMMSC https://lavky.com/radioproektor/
Offline
User avatar

rick.lang

  • Posts: 17175
  • Joined: Wed Aug 22, 2012 5:41 pm
  • Location: Victoria BC Canada

Re: Sound Devices MixPre-6 II (second generation)

PostFri Oct 04, 2019 5:14 pm

Robert, thanks. Both batteries took just over nine hours for their first charge. I’ll be using them Saturday on a shoot perhaps two hours untethered. The rest of the time the MixPre will be running with the DC Power supply.


Sent from my iPhone using Tapatalk
Rick Lang
Offline

Username

  • Posts: 389
  • Joined: Tue Jun 25, 2019 2:33 am
  • Real Name: Petter Flink

Re: Sound Devices MixPre-6 II (second generation)

PostFri Oct 04, 2019 6:26 pm

The mixpre first gens uses the AK557-series ADC.

The 3 is running a single AK5576 in a 6 to 3 summing setup.
The 6 uses the AK5578 in a 8 to 4 setup.
The 10 uses two AK5578 in 8 to 4 summing. One for each side of xlr inputs.
Grew up with a Nikon FM
Resolve & Fusion Studio 18.6
MBP M1 16GB/1TB
MM M1 16GB/512GB TB4 1TB & 2TB
MM i7 16GB/1TB & PowerColor Vega 56 8GB
Offline
User avatar

Dmytro Shijan

  • Posts: 1760
  • Joined: Wed Sep 17, 2014 7:15 pm
  • Location: UA

Re: Sound Devices MixPre-6 II (second generation)

PostFri Oct 04, 2019 6:34 pm

my mistake, but looks more like AK5558VN
Image
BMMCC/BMMSC Rigs Collection https://bmmccrigs.tumblr.com
My custom made accessories for BMMCC/BMMSC https://lavky.com/radioproektor/
Offline
User avatar

Dmytro Shijan

  • Posts: 1760
  • Joined: Wed Sep 17, 2014 7:15 pm
  • Location: UA

Re: Sound Devices MixPre-6 II (second generation)

PostFri Oct 04, 2019 6:45 pm

By the way, Tascam DR-100MKIII also use dual AKM chips to extend dynamic range, but it records only to 24bit. So formally this technology is not extremely new.
BMMCC/BMMSC Rigs Collection https://bmmccrigs.tumblr.com
My custom made accessories for BMMCC/BMMSC https://lavky.com/radioproektor/
Offline

Username

  • Posts: 389
  • Joined: Tue Jun 25, 2019 2:33 am
  • Real Name: Petter Flink

Re: Sound Devices MixPre-6 II (second generation)

PostFri Oct 04, 2019 7:27 pm

Dmitry Shijan wrote:my mistake, but looks more like AK5558VN
Image


Yes I know them from the FCC photos.
Those where most likely from the development stage. Probably due to the 557 series were not yet released or early in production.

The AK557x series was confirmed by Paul Isaacs himself.
https://www.gearslutz.com/board/showpos ... tcount=383
Last edited by Username on Fri Oct 04, 2019 7:58 pm, edited 1 time in total.
Grew up with a Nikon FM
Resolve & Fusion Studio 18.6
MBP M1 16GB/1TB
MM M1 16GB/512GB TB4 1TB & 2TB
MM i7 16GB/1TB & PowerColor Vega 56 8GB
Offline
User avatar

Rakesh Malik

  • Posts: 3236
  • Joined: Fri Dec 07, 2012 1:01 am
  • Location: Vancouver, BC

Re: Sound Devices MixPre-6 II (second generation)

PostFri Oct 04, 2019 7:56 pm

rick.lang wrote:Has anyone confirmed that Reaper will preserve Timecode values on their output? I’m going to try hopefully this week but working on some other issues as a top priority. Hope it’s in Resolve 16.1 GM.


I haven't had a chance to try it yet... argh. Too much to do, not enough time...

For now I'm planning on just staying with 24-bit recording, and hoping that Resolve gains 32-bit audio support soon.

Even if Reaper works, it would still make for a clunky workflow.
Rakesh Malik
Cinematographer, photographer, adventurer, martial artist
http://WinterLight.studio
System:
Asus Flow X13, Octacore Zen3/32GB + XG Mobile nVidia RTX 3080/16GB
Apple M1 Mini/16GB
Offline
User avatar

Robert Niessner

  • Posts: 4946
  • Joined: Thu Feb 21, 2013 9:51 am
  • Location: Graz, Austria

Re: Sound Devices MixPre-6 II (second generation)

PostFri Oct 04, 2019 11:37 pm

I have played around with Reaper a bit (I normally use it just for recording voice overs, so I'm no expert with Reaper).

For my tests I have used the Sound Devices 32_bit_float.WAV sample they provide on their website.

Make sure you set the project settings to the same frame rate like your footage.

Reaper can read the embedded timecode.

If you import your clips, you can right click and from "item processing" select "move items to source preferred position (BWF)".
That will place each clip to the correct timecode position of the track timeline.

Then I used "Normalize Items"

For exporting individual files:
Select them all. Go to "File -> Render".
In the "Render to File" dialog box set:

Source = Selected media items
... all selected items will be exported

[x] Tail = 0 ms
otherwise you will get a tail added

File name = $item
... that will restore the individual clip name when exporting, found under the button "Wildcards"

I was successfully able to render the 32-bit clip into a 24-bit normalized file, re-import it and by using "move items to source preferred position (BWF)" it got aligned correctly.
Saying "Thx for help!" is not a crime.
--------------------------------
Robert Niessner
LAUFBILDkommission
Graz / Austria
--------------------------------
Blackmagic Camera Blog (German):
http://laufbildkommission.wordpress.com

Read the blog in English via Google Translate:
http://tinyurl.com/pjf6a3m
Offline
User avatar

Dmytro Shijan

  • Posts: 1760
  • Joined: Wed Sep 17, 2014 7:15 pm
  • Location: UA

Re: Sound Devices MixPre-6 II (second generation)

PostSat Oct 05, 2019 11:58 am

Any info how 32Bit Float will work with compressors and software limiters in real life?
If your source have a lot of really loud splashes and you bring back loudest part to visible range in one click, other parts of track gain became too low. Simple normalize tool for selected regions only or manual gain adjust with curve is ok for simple situations, but for instant random loud splaches you need some kind of automatic limiter. So will those software plugins see that hidden dynamic range in 32Bit mode? Is it possible that software limiters in 32Bit mode will produce same result as analogue limiters or even better?
BMMCC/BMMSC Rigs Collection https://bmmccrigs.tumblr.com
My custom made accessories for BMMCC/BMMSC https://lavky.com/radioproektor/
Offline
User avatar

Dmytro Shijan

  • Posts: 1760
  • Joined: Wed Sep 17, 2014 7:15 pm
  • Location: UA

Re: Sound Devices MixPre-6 II (second generation)

PostSat Oct 05, 2019 12:23 pm

So I downloaded samples from SoundDevices website again and play with very simple AU limiter plugin in Cocos Reaper. Works great. All you need do is set attack/release time. Artifacts-free real time recovery!
BMMCC/BMMSC Rigs Collection https://bmmccrigs.tumblr.com
My custom made accessories for BMMCC/BMMSC https://lavky.com/radioproektor/
Offline
User avatar

rick.lang

  • Posts: 17175
  • Joined: Wed Aug 22, 2012 5:41 pm
  • Location: Victoria BC Canada

Re: Sound Devices MixPre-6 II (second generation)

PostSat Oct 05, 2019 2:31 pm

So Cocos Reaper is the AU plugin for Resolve?


Sent from my iPhone using Tapatalk
Rick Lang
Offline
User avatar

Dmytro Shijan

  • Posts: 1760
  • Joined: Wed Sep 17, 2014 7:15 pm
  • Location: UA

Re: Sound Devices MixPre-6 II (second generation)

PostSat Oct 05, 2019 2:54 pm

Cockos Reaper is standalone audio editor https://www.reaper.fm/

Here are processed examples:
https://www.dropbox.com/sh/rm6c9sdgimeo ... gKG7a?dl=0
BMMCC/BMMSC Rigs Collection https://bmmccrigs.tumblr.com
My custom made accessories for BMMCC/BMMSC https://lavky.com/radioproektor/
Offline
User avatar

rick.lang

  • Posts: 17175
  • Joined: Wed Aug 22, 2012 5:41 pm
  • Location: Victoria BC Canada

Re: Sound Devices MixPre-6 II (second generation)

PostSun Oct 06, 2019 1:44 am

Thanks, Dmitry. I was pretty tired this morning and after the shoot today, I’m dead now so hardly more functional. Maybe tomorrow. Your Cocos post makes perfect sense now but threw me this morning!


Sent from my iPhone using Tapatalk
Rick Lang
Offline
User avatar

Dmytro Shijan

  • Posts: 1760
  • Joined: Wed Sep 17, 2014 7:15 pm
  • Location: UA

Re: Sound Devices MixPre-6 II (second generation)

PostSun Oct 06, 2019 11:29 am

I preferred MixPre-3II over 6II because less cost, smaller form factor and more free space around rotary headphones button. MixPre-3 body also looks less ugly than MixPre-6. I can understand that lack of combo XLRs is due smaller size, but seems there is one more very odd artificial limitation of MixPre-3 series.

RECORDING: MixPre-6ii = 8 Tracks: stereo mix + 6 ISOs
RECORDING: MixPre-3ii = 5 Tracks: stereo mix + 3 ISO’s

My idea was to keep classic MixPre preamp, and use ultra compact MixPre-3II for everyday stereo field recording. And in some rare situations when i need more mic inputs i was thinking to plug MixPre to MixPre-3II line in and have 5 mic inputs total. But seems it will not work like this with MixPre-3II. It can record only 3 separate inputs.

Also if someone interested to read, here is Sound Devices patent application "High dynamic range analog-to-digital conversion with selective regression based data repair " https://patents.google.com/patent/US9654134B2/en

Image
BMMCC/BMMSC Rigs Collection https://bmmccrigs.tumblr.com
My custom made accessories for BMMCC/BMMSC https://lavky.com/radioproektor/
Offline

Brad Hurley

  • Posts: 2039
  • Joined: Wed Jan 17, 2018 7:42 pm
  • Location: Montréal

Re: Sound Devices MixPre-6 II (second generation)

PostSun Oct 06, 2019 2:30 pm

Kim Janson wrote:I wonder this hole fuss about the 32 bit float. Do not understand why float is needed or why 32 bits is needed.


This might help: https://www.sounddevices.com/32-bit-flo ... explained/
Resolve 18 Studio, Mac Pro 3.0 GHz 8-core, 32 gigs RAM, dual AMD D700 GPU.
Audio I/O: Sound Devices USBPre-2
Offline
User avatar

rick.lang

  • Posts: 17175
  • Joined: Wed Aug 22, 2012 5:41 pm
  • Location: Victoria BC Canada

Re: Sound Devices MixPre-6 II (second generation)

PostSun Oct 06, 2019 2:46 pm

It’s early days and in time it will emerge as invaluable or over-hyped. My acoustic music video (last shoot Monday) certainly doesn’t stretch any limits of 24bit audio even without limiters! But I used 32bit to get used to the new MixPre-6 II capabilities and operational characteristics as well as the post-processing in Resolve or Reaper.

But why bother? Since I don’t have a dedicated sound guy, I set up sound levels before takes, but once recording I can only monitor the MixPre output display to see all tracks are responding—I can’t adjust faders etc and leave it to the 32bit wizardry to be able to handle the situation. That’s my main attraction.

When previously recording in the BMD camera, I fairly often would experience clipping. It’s a comfort to know those days are in the past. But the greater experience and capabilities of others recording with 24bit audio may not need to switch to 32bit as the MixPre 24bit limiters may be completely sufficient. Perhaps after I have more experience, I’ll give 24bit a try as well.

I do feel I may be guilty of jumping on 32bit prematurely given I may not be able to manage 32bit completely from the Resolve Media page through the Deliver page! In the next week I hope to see if that limitation affects me, but I do expect Resolve to include full 32bit management end-to-end this year. Since Fairlight handles it, Resolve will follow, no?
Rick Lang
Offline

Brad Hurley

  • Posts: 2039
  • Joined: Wed Jan 17, 2018 7:42 pm
  • Location: Montréal

Re: Sound Devices MixPre-6 II (second generation)

PostSun Oct 06, 2019 2:54 pm

rick.lang wrote:But why bother? Since I don’t have a dedicated sound guy, I set up sound levels before takes, but once recording I can only monitor the MixPre output display to see all tracks are responding—I can’t adjust faders etc and leave it to the 32bit wizardry to be able to handle the situation. That’s my main attraction.


Indeed, I think that's the main attraction. It's going to be especially useful in documentary work or recording anything that's either unrehearsed or where the person doing the recording is unfamiliar with (and thus unprepared for) the full dynamic range of what's about to unfold. In a way it's the audio equivalent of recording raw video, although it's even better than that because you don't have to worry about clipping even if an unexpectedly loud sound occurs.
Resolve 18 Studio, Mac Pro 3.0 GHz 8-core, 32 gigs RAM, dual AMD D700 GPU.
Audio I/O: Sound Devices USBPre-2
Offline
User avatar

rick.lang

  • Posts: 17175
  • Joined: Wed Aug 22, 2012 5:41 pm
  • Location: Victoria BC Canada

Re: Sound Devices MixPre-6 II (second generation)

PostSun Oct 06, 2019 3:00 pm

Brad, looks like the marketing department missed an opportunity to promote 32bit, which is a bit stuffy and too many math implications, as “Audio raw” and not even talk about 32bit at all.


Sent from my iPhone using Tapatalk
Rick Lang
Offline

Brad Hurley

  • Posts: 2039
  • Joined: Wed Jan 17, 2018 7:42 pm
  • Location: Montréal

Re: Sound Devices MixPre-6 II (second generation)

PostSun Oct 06, 2019 3:07 pm

rick.lang wrote:Brad, looks like the marketing department missed an opportunity to promote 32bit, which is a bit stuffy and too many math implications, as “Audio raw” and not even talk about 32bit at all.


Ah, SDRAW and BRAW, a match made in heaven. :D
Resolve 18 Studio, Mac Pro 3.0 GHz 8-core, 32 gigs RAM, dual AMD D700 GPU.
Audio I/O: Sound Devices USBPre-2
Offline
User avatar

Dmytro Shijan

  • Posts: 1760
  • Joined: Wed Sep 17, 2014 7:15 pm
  • Location: UA

Re: Sound Devices MixPre-6 II (second generation)

PostSun Oct 06, 2019 3:13 pm

We need sensor with something like 5x gain circuits combined internally to something like 30 stops of dynamic range HDR BRAW to match current 32 bit HDR audio flexibility.
BMMCC/BMMSC Rigs Collection https://bmmccrigs.tumblr.com
My custom made accessories for BMMCC/BMMSC https://lavky.com/radioproektor/
Offline
User avatar

Dmytro Shijan

  • Posts: 1760
  • Joined: Wed Sep 17, 2014 7:15 pm
  • Location: UA

Re: Sound Devices MixPre-6 II (second generation)

PostSun Oct 06, 2019 3:33 pm

Who knows, maybe in future they will add 24bit float.
At least we have similar example for images - 32 float and 16 bit float EXR files which are also ok. You can try to post this idea to SD or Zoom support.
BMMCC/BMMSC Rigs Collection https://bmmccrigs.tumblr.com
My custom made accessories for BMMCC/BMMSC https://lavky.com/radioproektor/
Offline
User avatar

Dmytro Shijan

  • Posts: 1760
  • Joined: Wed Sep 17, 2014 7:15 pm
  • Location: UA

Re: Sound Devices MixPre-6 II (second generation)

PostSun Oct 06, 2019 4:41 pm

BMMCC/BMMSC Rigs Collection https://bmmccrigs.tumblr.com
My custom made accessories for BMMCC/BMMSC https://lavky.com/radioproektor/
Offline

Username

  • Posts: 389
  • Joined: Tue Jun 25, 2019 2:33 am
  • Real Name: Petter Flink

Re: Sound Devices MixPre-6 II (second generation)

PostSun Oct 06, 2019 5:30 pm

Dmitry Shijan wrote:Who knows, maybe in future they will add 24bit float.
At least we have similar example for images - 32 float and 16 bit float EXR files which are also ok. You can try to post this idea to SD or Zoom support.


24 bit float would be 16-but audio and 8-bit mantissa (resolution)
That would not really be that a step forward.

32-bit float for audio is a very good way for a lot of us.
Especially for us who does work alone, those recording volatile sound sources or simple just want a rec and forget kind of recorder.
Grew up with a Nikon FM
Resolve & Fusion Studio 18.6
MBP M1 16GB/1TB
MM M1 16GB/512GB TB4 1TB & 2TB
MM i7 16GB/1TB & PowerColor Vega 56 8GB
Offline

Mattias Murhagen

  • Posts: 298
  • Joined: Mon Nov 27, 2017 3:09 am
  • Location: New York

Re: Sound Devices MixPre-6 II (second generation)

PostMon Oct 07, 2019 2:10 pm

Kim Janson wrote:Thanks, I have seen that, and it probably is the main reason I feel negative about the 32 bit float. They completely fail to explain why 32 bit and why float.


I'm guessing they picked 32-bit float because many DAWs operate at that resolution internally. If you're using Pro Tools or Nuendo they'll both (unless set differently) default to 32-bit float even if you're importing and playing back 24-bit fixed audio files. The conversion is in the background so we don't see it, but it's there.

Also like the previous poster wrote the actual range of the signal that is described is about 23 or 24 bits fixed in a 32-bit float file, if memory serves me. So that's maybe what they were referring to when they wrote 0dBFS float = 0dBFS fixed (16 and 24 bit).

It really seems to me that this functionality is mostly a matter of convenience.

My only worry is that it'll eventually translate to inconvenience on the audio-post side of things with plenty of recordings going above 0dBFS that then need to get significantly trimmed down. For sure better than clipping or excessive noise, but still less than ideal.
Offline
User avatar

Dmytro Shijan

  • Posts: 1760
  • Joined: Wed Sep 17, 2014 7:15 pm
  • Location: UA

Re: Sound Devices MixPre-6 II (second generation)

PostMon Oct 07, 2019 2:14 pm

By the way, my 18650 Battery Enclosure Module can be mounted directly at the top of MixPre and combined with DC Power to USB Type-C Adapter Converter can power MixPre all day. It may be not too slim form factor, but at least feels like rugged single brick stack.

https://lavky.com/handmade/home-and-hob ... t=UW590888
https://lavky.com/handmade/home-and-hob ... t=AM429494

Image
Image
Image
BMMCC/BMMSC Rigs Collection https://bmmccrigs.tumblr.com
My custom made accessories for BMMCC/BMMSC https://lavky.com/radioproektor/
Offline
User avatar

rick.lang

  • Posts: 17175
  • Joined: Wed Aug 22, 2012 5:41 pm
  • Location: Victoria BC Canada

Re: Sound Devices MixPre-6 II (second generation)

PostFri Oct 11, 2019 4:58 pm

When I made my recent recordings using Timecode, I left the ubits all zeros. Now I’m thinking I should use them to record CC:YY:MM:DD such as 20191011 to complement the Timecode HH:MM:SS:FF. Is that of any value in metadata to sort and sync clips by Timecode recorded over a period of time?

The Timecode Mode has a downward arrow and upwards arrow to select a Mode. It defaults to U:U:U:U which seems the only appropriate mode for a date CC:YY:MM:DD. When I select Mode D:M:Y:U, it does rearrange the values automatically but that’s not the smartest sort sequence.

I’m trying to determine how best to handle audio recorded potentially spanning a period of months or years for one project. That audio will need to be synced to video.


Sent from my iPhone using Tapatalk
Rick Lang
Offline
User avatar

dondidnod

  • Posts: 633
  • Joined: Sun Nov 25, 2018 7:52 am
  • Location: Castro Valley, CA
  • Real Name: Donald Keller

Re: Sound Devices MixPre-6 II (second generation)

PostSat Oct 12, 2019 6:43 pm

When this topic got started, Rick and I were on the waiting list for the backordered hit of the NAB show, the Zoom F6. We changed our minds and bought the Sound Devices MixPre6 II instead. Was it worth the extra money?

To answer this I borrowed a Zoom F8, which has the same preamps as the F6, and put them both through their paces. With my untrained singing voice, I recorded two songs at 24 bit, 48 kHz using a Sennheiser MKE 600 Supercardiod (no pop filter) in a recording booth. No limiter was configured on either recorder, as I was trying to test the ability of each pre-amp to respond to the rapid amplitude rise of my voice, to see how musical it is when overdriven.

I normalized the sound clips in Avid Pro Tools and edited them with phrases back to back. I sang Hallelujah and Thunderball. Most of the differences can be found if you fast forward to 3:40.

At the end of Thunderball, the F8 clipped, so I did a second take of both devices. Here is the waveform showing the flat ceiling of the last word "Thunderball" in the ending two takes using the Zoom F8. The first take of that word on the MixPre6 II I must have started off axis on "ball" to prevent clipping. On the second take it was direct into the Mic and it should have clipped more than it did.
MixPre6&F8Waveforms.jpg
Audio waveform - MixPre6 II top left Zoom F8 bottom right
MixPre6&F8Waveforms.jpg (197.22 KiB) Viewed 501412 times

The back to back comparison is here:


The Sound Devices MixPre6 II has greater headroom and better damping than the F8. It was more revealing of imperfections that may have to be dealt with in post. I got a good result from the Zoom F8 most of the time, but under extreme circumstances, the Sound Design's class A Kashmir pre-amps are worth the extra juice they consume. The unprocessed signal of the Zoom F8 was less complex, with very light, almost unnoticeable smearing of the details, sort of an equalization of the signal. I disliked hearing my voice during tracking on the MixPre6 II because it revealed everything in my windpipe but later it sounded okay on playback. Maybe the Zoom F6 was the first to announce 32 bit float recording because it needed it more to deal with the tendency to clip on loud passages.

Yes, it was worth the extra $200.00 USD. Just check out the resale value of older models to see that I'm not alone in this observation.

Thanks to the Broadcast Engineering and Media Arts dept. at City College of San Francisco for the use of their studio and equipment.
Last edited by dondidnod on Sat Oct 12, 2019 9:37 pm, edited 6 times in total.
Offline
User avatar

rick.lang

  • Posts: 17175
  • Joined: Wed Aug 22, 2012 5:41 pm
  • Location: Victoria BC Canada

Sound Devices MixPre-6 II (second generation)

PostSat Oct 12, 2019 7:53 pm

Thanks for that comparison, Don! Very entertaining as well as informative. I think your singing supports what others have claimed regarding the performance of the Sound Devices MixPre II. I’m in the very early stage of beginning to work with audio recorded for the music videos and I didn’t know if my new Line Audio Design CM-4 mics or the MixPre were giving me the rich sound. It’s probably both working well together.

I’ve also heard how low the noise floor remains when increasing the audio level in post. That is so important given volumes occasionally drop lower than I anticipate. And the clapping of hands is another bothersome characteristic of recording performances and that seems to be handled better now.


Sent from my iPhone using Tapatalk
Rick Lang
Offline

OwenCrowley

  • Posts: 84
  • Joined: Thu Aug 10, 2017 12:58 am

Re: Sound Devices MixPre-6 II (second generation)

PostSat Oct 19, 2019 11:26 am

Hey folks, I just posted what is apparently the first request for 32-bit audio support in
DaVinci Resolve » DaVinci Resolve Feature Requests

As we are jonesing for Resolve to support what the MixPres and Zoom can produce, it might help drive priority if people jump over there and +1 my request.
Offline
User avatar

rick.lang

  • Posts: 17175
  • Joined: Wed Aug 22, 2012 5:41 pm
  • Location: Victoria BC Canada

Re: Sound Devices MixPre-6 II (second generation)

PostSat Oct 19, 2019 3:14 pm

My understanding is that normalizing 32bit audio has been working in Fairlight but any adjustment has not been passed on to Deliver. I see in Resolve 16.1 final that Deliver can now “decode 32bit” but I don’t understand if that means it’s now handling 32bit audio that has been adjusted in Fairlight.


Sent from my iPhone using Tapatalk
Rick Lang
Offline

Tom Donalek

  • Posts: 49
  • Joined: Wed Apr 23, 2014 4:31 pm

Re: Sound Devices MixPre-6 II (second generation)

PostSun Oct 20, 2019 5:53 am

OwenCrowley wrote:Hey folks, I just posted what is apparently the first request for 32-bit audio support in
DaVinci Resolve » DaVinci Resolve Feature Requests

As we are jonesing for Resolve to support what the MixPres and Zoom can produce, it might help drive priority if people jump over there and +1 my request.


I looked through recent posts on a couple of feature request threads, but I didn't see your post. Can you put a link here for me to follow to reinforce your request?
Offline

OwenCrowley

  • Posts: 84
  • Joined: Thu Aug 10, 2017 12:58 am

Re: Sound Devices MixPre-6 II (second generation)

PostSun Oct 20, 2019 3:53 pm

Tom Donalek wrote:
OwenCrowley wrote:Hey folks, I just posted what is apparently the first request for 32-bit audio support in
DaVinci Resolve » DaVinci Resolve Feature Requests

As we are jonesing for Resolve to support what the MixPres and Zoom can produce, it might help drive priority if people jump over there and +1 my request.


I looked through recent posts on a couple of feature request threads, but I didn't see your post. Can you put a link here for me to follow to reinforce your request?


Hopefully this link will work:
https://forum.blackmagicdesign.com/viewtopic.php?f=33&t=100973
PreviousNext

Return to Cinematography

Who is online

Users browsing this forum: Adam Langdon, Google [Bot] and 101 guests