yesterday a livestream by means of ATEM mini extreme and a BMPCC 6kpro.
my previous solution to disable the camera control with the
bidirectional micro converter also failed by using the new 3G converter.
so the 6k pro again directly to the ATEM and thus I started the stream.
we also always record this in the camera, but yesterday it was so that the camera
interrupted the recording every moment.
was used as always an angelbird CF pro Cfast2.0 card.
was recorded, due to the limitation by the camera control in 6kdci BRAW with 25fps.
in the evening after the stream i did some tests to see if the camera (was used the first time)
or the card was the problem.
without connecting to the ATEM, recordings up to the full capacity of the card were
possible without interruption.
as soon as the HDMI cable was reconnected to the camera, the interruptions were back.
but when using the old bidirectional converter, the camera control was deactivated again.
(for setup see at the old picture)
so i ask BMD to take care of this problem and finally give us the possibility to prevent
the camera control either in the ATEM software or in the camera.
but also the possibility to use again at control of the camera via the ATEM recording in prores,
because here the BRAW 6k files are unnecessary and a madness!!!!
ATEM mini extreme firmware 8.6.1
ATEM software control 8.6.4
BMPCC 6k pro firmware 7.3.1
micro biconverter 3G firmware 7.5.3
micro biconverter firmware (latest ??? - cannot see in the app - but should 7.3.2)
.
old picture of a working setup without camera control:
my previous solution to disable the camera control with the
bidirectional micro converter also failed by using the new 3G converter.
so the 6k pro again directly to the ATEM and thus I started the stream.
we also always record this in the camera, but yesterday it was so that the camera
interrupted the recording every moment.
was used as always an angelbird CF pro Cfast2.0 card.
was recorded, due to the limitation by the camera control in 6kdci BRAW with 25fps.
in the evening after the stream i did some tests to see if the camera (was used the first time)
or the card was the problem.
without connecting to the ATEM, recordings up to the full capacity of the card were
possible without interruption.
as soon as the HDMI cable was reconnected to the camera, the interruptions were back.
but when using the old bidirectional converter, the camera control was deactivated again.
(for setup see at the old picture)
so i ask BMD to take care of this problem and finally give us the possibility to prevent
the camera control either in the ATEM software or in the camera.
but also the possibility to use again at control of the camera via the ATEM recording in prores,
because here the BRAW 6k files are unnecessary and a madness!!!!
ATEM mini extreme firmware 8.6.1
ATEM software control 8.6.4
BMPCC 6k pro firmware 7.3.1
micro biconverter 3G firmware 7.5.3
micro biconverter firmware (latest ??? - cannot see in the app - but should 7.3.2)
.
old picture of a working setup without camera control:
- Attachments
-
- IMG_6222.jpeg (304.97 KiB) Viewed 2157 times
cMP 5.1 2x3,46/96GB/2x2TB SSD/4x4TB/7101A 4x2TB 970evo+/HP1344/BMD4k/RadeonVII
macOS 12.6.3
BMPCC 6k pro (7.9.1)
meike s35 cine 25mm, 35mm, 50mm, 75mm
resolve studio 18.1.4
mini panel
speed editor
desktop video 12.1
intensity pro 4k
atem extreme (8.6.1)
macOS 12.6.3
BMPCC 6k pro (7.9.1)
meike s35 cine 25mm, 35mm, 50mm, 75mm
resolve studio 18.1.4
mini panel
speed editor
desktop video 12.1
intensity pro 4k
atem extreme (8.6.1)